Return to fdisk.8 CVS log

Up to [cvs.NetBSD.org] / src / sbin / fdisk

386bsd -> NetBSD

.\"	$Id: fdisk.8,v 1.3 1993/12/06 09:32:27 cgd Exp $	-*- nroff -*-
.Dd April 4, 1993
.Dt FDISK 8
.\".Os BSD 4
.Sh NAME
.Nm fdisk
.Nd DOS partition maintainance program
.Sh SYNOPSIS
.Nm
.Op Fl i
.Op Fl u
.Bl -tag -width time
.It Fl i
Initializes sector 0 of the disk.
.It Fl u
Is used for updating (editing) sector 0 of the disk.
.El
.Sh PROLOGUE
In order for the BIOS to boot the kernel,
certain conventions must be adhered to.
Sector 0 of the disk must contain boot code,
a partition table,
and a magic number.
BIOS partitions can be used to break the disk up into several pieces.
The BIOS brings in sector 0
(does it really use the code?)
and verifies the magic number.
It then searches the 4 BIOS partitions described by sector 0
to determine which of them is
.Em active.
This boot then brings in the secondary boot block from the
.Em active
partition and runs it.
Under DOS,
you could have one or more partitions with one
.Em active.
The DOS
.Nm
program can be used to divide space on the disk into partitions and set one
.Em active.
.Sh DESCRIPTION
The NetBSD program
.Nm
serves a similar purpose to the DOS program.
When called with no arguments, it prints the sector 0 partition table.
An example follows:

.Bd -literal
	******* Working on device /dev/rwd0d *******
	parameters extracted from in-core disklabel are:
	cylinders=769 heads=15 sectors/track=33 (495 blks/cyl)

	parameters to be used for BIOS calculations are:
	cylinders=769 heads=15 sectors/track=33 (495 blks/cyl)
		
	Warning: BIOS sector numbering starts with sector 1
	Information from DOS bootblock is:
	The data for partition 0 is:
	sysid 165,(NetBSD)
    	    start 495, size 380160 (185 Meg), flag 0
		beg: cyl 1/ sector 1/ head 0;
		end: cyl 768/ sector 33/ head 14
	The data for partition 1 is:
	sysid 164,(unknown)
    	    start 378180, size 2475 (1 Meg), flag 0
		beg: cyl 764/ sector 1/ head 0;
		end: cyl 768/ sector 33/ head 14
	The data for partition 2 is:
	<UNUSED>
	The data for partition 3 is:
	sysid 99,(ISC UNIX, other System V/386, GNU HURD or Mach)
    	    start 380656, size 224234 (109 Meg), flag 80
		beg: cyl 769/ sector 2/ head 0;
		end: cyl 197/ sector 33/ head 14
.Ed
.Pp
The disk is divided into three parititions that happen to fill the disk.
The second partition overlaps the end of the first.
(Used for debugging purposes)
.Bl -tag -width "cyl, sector and head"
.It Em "sysid"
is used to label the partition.  NetBSD reserves the
magic number 165 decimal (A5 in hex).
.It Em "start and size"
fields provide the start address
and size of a parition in sectors.
.It Em "flag 80"
specifies that this is the active partition.
.It Em "cyl, sector and head"
fields are used to specify the beginning address
and end address for the parititon.
.It Em "Note:"
these numbers are calculated using BIOS's understanding of the disk geometry
and saved in the bootblock.
.El
.Pp
The flags
.Fl i
or
.Fl u
are used to indicate that the paritition data is to be updated.
The
.Nm
program will enter a conversational mode.
This mode is designed not to change any data unless you explicitly tell it to.
.Nm
selects defaults for its questions to guarantee the above behaviour.
.Pp
It displays each partition
and ask if you want to edit it.
If you say yes,
it will step through each field showing the old value
and asking for a new one.
When you are done with a partition,
.Nm
will display it and ask if it is correct.
.Nm
will then procede to the next entry.
.Pp
Getting the
.Em cyl, sector,
and
.Em head
fields correct is tricky.
So by default,
they will be calculated for you;
you can specify them if you choose.
.Pp
After all the partitions are processed,
you are given the option to change the
.Em active
partition.
Finally,
when the all the data for the first sector has been accumulated,
you are asked if you really want to rewrite sector 0.
Only if you answer yes,
will the data be written to disk.
.Pp
The difference between the
.Fl u
flag and
.Fl i
flag is that
the
.Fl u
flag just edits the fields as they appear on the disk.
While the
.Fl i
flag is used to "initialize" sector 0;
it will setup the last BIOS partition to use the whole disk for NetBSD;
and make it active.
.Sh NOTES
.Pp
The automatic calculation of starting cylinder etc. uses
a set of figures that represent what the BIOS thinks is the
geometry of the drive.
These figures are by default taken from the incore disklabel,
but the program initially gives you an oportunity to change them.
This allows the user to create a bootblock that can work with drives
that use geometry translation under the BIOS.
.Pp
If you hand craft your disk layout,
please make sure that the NetBSD partition starts on a cylinder boundary.
A number of decisions made later may assume this.
(This might not be necessary later.)
.Pp
Editing an existing partition will most likely cause you to
lose all the data in that partition.
.Pp
You should run this program interactively once or twice to see how it works.
This is completely safe as long as you answer the last question in the negative.
There are subtleties
that the program detects
that are not fully explained in this manual page.
.Sh SEE ALSO
.Xr disklabel 8
.Sh BUGS
One less now, but probably more